We go beyond paving by offering consistent and superior service, sophisticated project management, and high-quality materials & workmanship to the Canada market. Please browse our extensive solution offering:
Click Solution Title or Icon to Learn More.
As pavement ages, fine hairline cracks spread and deepen within the asphalt. Irritants such as water, oil, and UV rays enter through cracks and weaken the substrate. This may result in pavement heaving or isolated sections of alligator cracking. For full technical specs, please click here.
With a high rate of exposure to the sun’s ultraviolet rays and its damaging effects, parking lots oxidize (or fade) much quicker than other structures. Combat a gray, faded parking lot with routine seal coating every two to three years, which not only helps protect the pavement, it also provides a jet-black finish. Rose Paving offers a true, two-coat application. This technique requires cure time in between application of the first and second coats. This curing is critical to the overall effectiveness of the procedure. Once a final coat is applied, be sure to allow at least 24 hours before use of the parking lot. Asphalt-based emulsion sealer is applied using a squeegee or spray method. Air and surface temperature must be 60 degrees and rising. For full technical specs, please click here.
Re-striping is a necessity for busy parking lots. Generally speaking, however, the procedure should occur every 2-3 years. In addition to re-striping, Rose Paving can also help with layout and design for a newly resurfaced parking lot. There are many options to review based on your lot size, traffic load, and ADA requirements. Striping and stenciling can be performed in a variety of colors and we can also assist with any signage needs. For full technical specs, please click here.
Over time, due to wear and tear, all asphalt breaks down and cracks form. Usually, the first sign of deterioration is hairline or reflective cracks. Paying attention to cracks and applying sealant in a timely manner is the most beneficial service that can be performed on a parking lot because it slows the infiltration of water to the sub-base. Keep a close eye on open cracks, uneven transitions, and asphalt depressions; when cracks measure between ¼-inch and 1-inch wide, schedule cracksealing treatment. Once crackseal has been performed, follow up with sealcoat to help decelerate future cracking. For full technical specs, please click here.
Settling of poorly compacted fill also contributes to failure or instability. Removing and replacing damaged concrete is imperative to keep structures in top condition while also alleviating potential liabilities. Inspect concrete pavement routinely, but especially during the winter months, to catch defects early. Common procedures include repairing concrete sidewalks, stairs, curbs, gutters, dumpster pads, dock pads, parking bumpers, walls, ramps, and catch basins. For full technical specs, please click here.
In an effort to construct and operate buildings more efficiently, builders and owners are now utilizing “green” innovations to execute jobs. For exactly this purpose, our Special Projects Division is devoted to researching and developing eco-friendly paving solutions. From this division we have created a special service line – Green Paving Solutions™. Within this offering, we have solutions for storm-water management as well as concrete and asphalt alternatives. Ask your Rose Paving representative about permeable pavers, pervious concrete, porous asphalt, or low-VOC striping paints and learn how you can save energy, reduce waste and pollution, lower carbon footprint, and save costs.
Excess precipitation can cause catch basins to work overtime to properly drain your parking lot. That is why we advise inspecting your catch basins regularly and especially after a good rainfall or seasonal snow melting. Take note of standing water or other erosion such as raveling around the edges. These signs indicate it is time to repair surrounding pavement and adjust the basin height or replace the rings. Remember, if caught early, catch basin repairs can help prevent problem areas from spreading and weakening surrounding pavement. For full technical specs, please click here.
Infrared asphalt repair technology uses infrared light rays to heat an area of pavement, enabling quick removal of failed asphalt. This technology is ideal for critical repairs such as pavement depressions, trip hazards, potholes, and rough surfaces in drive lanes. New material is applied and compacted all with the same machinery. The procedure is faster than traditional removal and replacement, which means little disruption to you and your customers or tenants. It is a cost-effective and efficient option for retail or restaurant locations with little downtime as well as apartment communities and hospitals that require continuous access. For full technical specs, please click here.
Assess the number and location of catch basins on your parking lot. In many cases, slope is not achieved uniformly throughout a parking lot and lower spots may exist. Catch basins should be located in those areas to help water exit the surface. Catch basin installation begins by excavating the area as needed and installing a pre-cast concrete catch basin with necessary adjustment rings. Next, a cast-iron frame and lid is installed on the basin and set at the appropriate height for proper drainage. The excavated area is backfilled with crushed aggregate, leveled, and compacted. Finally, we recommend installing reinforced concrete around the perimeter for added strength. For full technical specs, please click here.
Generally speaking, parking lots wrequire reconstruction roughly ever 12 years. This time-frame may be longer or shorter based on the amount of routine preventative maintenance performed on the pavement. If maintenance has been deferred, however, or if the sub-base has deteriorated due to other site-specific factors, it becomes necessary to perform rehabilitation or reconstruct the pavement, whether in sections or in its entirety. Before reconstruction, identify and understand what is causing pavement failure. If water is a common problem, alternative under-drain solutions may be required. Additionally, to combat drainage problems, asphalt thickness may need to be increased. For full technical specifications, please click here.
Even with ideal conditions and routine preventative maintenance, asphalt resurfacing is recommended every 5-10 years on commercial sites and between 5-7 years on industrial sites with heavy truck traffic. However, every parking lot is unique; therefore, it is best to perform routine inspections and take careful note of any grade depressions or widespread areas of cracking. If these defects are apparent, resurfacing is a long-term and cost-effective solution. For this procedure, air and surface temperature must be 45 degrees and rising. Standard resurfacing includes a 1.5-inch to 2-inch asphalt topping overlay. The materialis feathered for a smooth transition to curb and gutter lines. For full technical specs, please click here.